Frequency response analysis of cylindrical shells conveying fluid using finite element method

A finite element vibration analysis of thin-watled cylindrical shells conveying fluid with uniform velocity is presented The dynamic behavior of thin-walled shell is based on the Sanders’ theory and the fluid in cyhndrical shell is considered as inviscid and incompressible so that it satisfies the Laplace’s equation A beam-like shell element is used to reduce the number of degrees-of-freedom by restricting to the circumferential modes of cylindrical shell An estimation of frequency response function of the pipe considering of the coupled effects of the internal fluid is presented A dynamic coupling condition of the interface between the fluid and the structure is used The effective thickness of fluid according to circumferential modes is also discussed The influence of fluid velocity on the frequency response function is illustrated and discussed The results by this method are compared with published lesults and those by commercial tools     

A rapid method for the simultaneous determination of 25 anti-hypertensive compounds in dietary supplements using ultra-high-pressure liquid chromatography

A novel, stable, simple and specific ultra-performance liquid chromatography method with ultraviolet detection (205 nm) for the simultaneous analysis of 25 anti-hypertensive substances was developed. The method was validated according to the International Conference of Harmonisation guidelines with respect to linearity, accuracy, precision, limit of detection (LOD), limit of quantitation (LOQ) and stability. From the ultra-performance liquid chromatography results, we identified the LOD and LOQ of solid samples to be 0.20–1.00 and 0.60–3.00 μg ml^?1, respectively, while those of liquid samples were 0.30–1.20 and 0.90–3.60 μg ml^?1, respectively. The linearity exceeded 0.9999, and the intra- and inter-day precisions were 0.15–6.48% and 0.28–8.67%, respectively. The intra- and inter-day accuracies were 82.25–111.42% and 80.70–115.64%, respectively, and the stability was lower than 12.9% (relative standard deviation). This method was applied to the monitoring of 97 commercially available dietary supplements obtained in Korea, such as pills, soft capsules, hard capsules, liquids, powders and tablets. The proposed method is accurate, precise and of high quality, and can be used for the routine, reproducible analysis and control of 25 anti-hypertensive substances in various dietary supplements. The work presented herein may help to prevent incidents related to food adulteration and restrict the illegal food market.     

Prognosis of breast cancer is associated with one-carbon metabolism related nutrients among Korean women

ABSTRACT: BACKGROUND: The 5-year survival rate for breast cancer among Korean women has increased steadily; however, breast cancer remains the leading cause of cancer mortality among women. One-carbon metabolism, which requires an adequate supply of methyl group donors and B vitamins, may affect the prognosis of breast cancer. This aim of this study was to investigate the associations of dietary intake of vitamin B2, vitamin B6 and folate before diagnosis on the prognosis of breast cancer. METHODS: We assessed the dietary intake using a food frequency questionnaire with 980 women who were newly diagnosed and histopathologically confirmed to have primary breast cancer from hospitals in Korea, and 141 disease progression events occurred. Cox's proportional hazard regression models were used to estimate the hazard ratio (HR) and 95% confidence interval (95% CI) adjusting for age, education, recruitment sites, TNM stage, hormone status, nuclear grade and total calorie. RESULTS: There was no significant association between any one-carbon metabolism related nutrients (vitamin B2, B6 and folate) and the progression of breast cancer overall. However, one-carbon metabolism related nutrients were associated with disease progression in breast cancer patients stratified by subtypes. In ER + and/or PR + breast cancers, no association was observed; however, in ER--/PR-- breast cancers, a high intake of vitamin B2 and folate statistically elevated the HR of breast cancer progression (HR = 2.28; 95% CI, 1.20-4.35, HR = 1.84; 95% CI, 1.02-3.32, respectively) compared to a low intake. This positive association between the ER/PR status and progression of the disease was profound when the nutrient intakes were categorized in a combined score (Pinteraction = 0.018). In ER--/PR-- breast cancers, high combined scores were associated with a significantly poor DFS compared to those belonging to the low score group (HR = 3.84; 95% CI, 1.70-8.71). CONCLUSIONS: In conclusion, our results suggest that one-carbon related nutrients have a role in the prognosis of breast cancer depending on the ER/PR status.     

Starch–methylcellulose–whey protein film properties

Four % (wt/wt) aqueous solutions were prepared at corn starch:methylcellulose:whey protein isolate (CS:MC:WPI) ratios of 2:2:2, 1:2:3, 2:1:3, 2:2:0, 1:2:0 and 2:1:0. Glycerol (gly) was used as a plasticiser at CS–MC–WPI:gly ratios of 2:1, 2.5:1 and 3:1. CS–MC–WPI blend films were stronger than CS–WPI films and had lower oxygen permeability (OP) than MC–WPI films. The highest tensile strength (TS) of blend films was 8.01 ± 3.41 MPa, at CS:MC:WPI ratio of 2:2:0 and CS–MC–WPI:gly ratio of 3:1. Lowest OP value was 45.05 ± 7.24 cm³ μm m^?2 per day kPa^?1, at CS:MC:WPI ratio of 2:2:2 and CS–MC–WPI:gly ratio of 3:1. OP values were predictable based on relative amounts of components. However, TS and elastic modulus properties of the CS–MC–WPI blend films did not reflect the relative amounts of the components. All of CS–MC–WPI films were translucent indicating some degree of immiscibility among the CS, MC and WPI. These results indicate the influence of complex molecular interactions among the components.     

Pre- and post-peak toughening behaviours of fibre-reinforced hot-mix asphalt mixtures

Recycled plastic fibre-reinforced hot-mix asphalt (HMA) mixtures have better fatigue resistance than plain HMA. The toughening effects of recycled plastic fibre-reinforced HMA were characterised using direct tensile loading tests. Adding a small quantity of recycled plastic fibres to HMA was found to significantly increase the mixture's fracture energy and toughness, which were calculated using the pre- and post-peak stages of tensile force–displacement curves. A theoretical model representing the pre-peak behaviour of fibre-reinforced HMA with direct tension-softening curves for various fibre contents is presented here. The enhanced toughness through post-peak analysis was also observed using toughness indices associated with fibre-bridging effect after the pre-peak composite stress. The pre-peak fracture energy model and post-peak toughness indices appeared to be governed by the direct tensile toughening of fibre-reinforced HMA's enhanced fibre-bridging effects. The pre-peak fracture energy model demonstrates the effect of fibre content on the strain energy density during the pull-out process within the pre-peak composite stress region. The maximum pre-peak fracture energy of a coarse-graded HMA mixed with recycled plastic fibres is achieved at a fibre content of 0.4% of the total weight of the HMA. The increases in the toughness indices within the post-peak composite stress region indicate that the fatigue resistance of fibre-reinforced HMA is at least 30% greater than that of control HMA.     

Development of an Automated Method for Folin‐Ciocalteu Total Phenolic Assay in Artichoke Extracts

Abstract: We developed a system to run the Folin‐Ciocalteu (F‐C) total phenolic assay, in artichoke extract samples, which is fully automatic, consistent, and fast. The system uses 2 high performance liquid chromatography (HPLC) pumps, an autosampler, a column heater, a UV/Vis detector, and a data collection system. To test the system, a pump delivered 10‐fold diluted F‐C reagent solution at a rate of 0.7 mL/min, and 0.4 g/mL sodium carbonate at a rate of 2.1 mL/min. The autosampler injected 10 μL per 1.2 min, which was mixed with the F‐C reagent and heated to 65 °C while it passed through the column heater. The heated reactant was mixed with sodium carbonate and color intensity was measured by the detector at 600 nm. The data collection system recorded the color intensity, and peak area of each sample was calculated as the concentration of the total phenolic content, expressed in μg/mL as either chlorogenic acid or gallic acid. This new method had superb repeatability (0.7% CV) and a high correlation with both the manual method (r²= 0.93) and the HPLC method (r²= 0.78). Ascorbic acid and quercetin showed variable antioxidant activity, but sugars did not. This method can be efficiently applied to research that needs to test many numbers of antioxidant capacity samples with speed and accuracy.     

High‐Precision Temperature‐Controllable Metal‐Coated Polymeric Molds for Programmable,Hierarchical Patterning

Nanofabrication is an indispensable process in nanoscience and nanotechnology. Unconventional lithographic techniques are often used for fabrication as alternatives to photolithography because they are faster, more cost‐effective, and simpler to use. However, these techniques are limited in scalability and utility because of the collapse of preprinted structures during step‐and‐repeat processes. This study proposes a new class of temperature‐controllable polymeric molds that are coated with a metal such that any site‐specific patterning can be accomplished in a programmable manner using selective contact‐dewetting lithography. The lithography allows sub‐100 nm patterning, step‐and‐repeat processing, and hierarchical structure fabrication. The programmable feature of the lithography can be utilized for the structural coloring and shaping of objects. Large‐area programmable patterning, semiconductor device manufacturing, and the fabrication of iridescent security devices would benefit from the unique features of the proposed strategy.